Fine surface finishFine grain · 1–2 mm
Fine, homogeneous surface finish. Primarily for walls, plinths, stairs and decorative surfaces, but also suitable for floors.
- Grain
- 1–2 mm
- On walls
- 2–4 mm
- On floors
- 4–6 mm
Not suitable for vehicle traffic.
Pre-mixed · single-component
VIRANIX 1K stone carpet
Factory pre-mixed surface covering made of natural marble pebbles with a water-based binder. Stir thoroughly and you are ready to start: on floors, walls and stairs, indoors and outdoors.
- Kitchen
- Bathroom
- Stairs
- Wall
- Terrace
- Hallway
Benefits
Why VIRANIX 1K?
Not just a surface covering, but a system: substrate preparation, primer, stone carpet and topcoat together deliver the result.
-
Joint-free surface
A continuous, seamless covering: no grout joints where dirt can settle.
-
Factory pre-mixed
No component dosing or mixing ratios: simply stir thoroughly before use.
-
Water-based binder
Selected natural marble pebbles with a flexible, water-based binder.
-
Well-defined layer build-up
TERRALOCK 1K primer, stone carpet and PRIMECOAT 2K topcoat: every layer is part of the system.
-
On floors and walls
It also holds on vertical surfaces, so floor and wall can share the same look.
-
Over old tiles, too
Stable, matted tiles first receive a quartz-sand BETOGRIP bonding bridge, followed by TERRALOCK 1K primer.
Layer build-up
How it is built up
Four steps, always in this order. Stone carpet does not hide a poor substrate, so no step can be skipped.
Substrate
A sound, clean substrate free of dust and grease: moisture max. 9%, pH max. 10, fresh concrete at least 28 days old. Repair any breakouts first.
REPAIR 800 R4Priming
Apply TERRALOCK 1K with a roller in a thin, continuous layer, approx. 0.15 kg/m². It binds dust and forms a bonding bridge.
TERRALOCK 1KSpreading and compacting
Spread and compact in a single step with a stainless steel trowel, between +10 and +30 °C, at max. 80% relative humidity.
Stone carpet colors
Sealing
After full cure, two thin coats of PRIMECOAT 2K, approx. 150 g/m² per coat. For vehicle traffic, use PRIMECOAT 2K PRO.
PRIMECOAT 2K
Videos
How it is made
Real installations, from priming to sealing.
-
VIRANIX 1K stone carpetInstallation -
Kitchen renovation over old tilesPart 1 -
Kitchen renovation over old tilesPart 2 -
Kitchen renovation over old tilesPart 3 -
Finished surface1K stone carpet -
Mixing the topcoatPRIMECOAT 2K -
Sealing with a rollerPRIMECOAT 2KGuide
Range
Two grain sizes
25 colors (KSZ01–KSZ25) in two grain sizes. The intended use determines which one is the better choice.
Fine surface finish
Most versatileMedium grain · 2–4 mm
Natural stone look with a uniform surface finish. For terraces, stairs and balconies, and indoors for hallways, kitchens and garages.
- Grain
- 2–4 mm
- On floors
- 4–6 mm
- Vehicles
- 6–8 mm
For vehicle traffic, 6–8 mm and a PRIMECOAT 2K PRO topcoat are mandatory.
Applications
Where can it be used?
Indoors and outdoors. The layer build-up and thickness are always matched to the surface and the load.
-
Kitchen
Also over old tiles, with proper preparation.
-
Bathroom
Joint-free, easy-to-clean surface with PRIMECOAT 2K.
-
Stairs
Indoor and outdoor stairs, with edge protection profiles.
-
Walls, plinths
In a 2–4 mm layer, using fine-grain material.
-
Terrace, balcony
Renovation of outdoor surfaces, with a slope and a topcoat.
-
Garage
Medium grain, 6–8 mm, with PRIMECOAT 2K PRO topcoat.
Technical data
How much material do I need?
Guide values for net, level surfaces. Allow extra for uneven substrates; the calculator gives you the exact quantity.
- Walls, plinths
- 2–4 mm · 6–9 kg/m²
- Foot traffic
- 4–6 mm · 9–12 kg/m²
- Vehicle traffic
- 6–8 mm · 12–15 kg/m² (medium grain)
- Packaging
- 25 kg bucket
- Primer – TERRALOCK 1K
- approx. 0.15 kg/m²
- Topcoat – PRIMECOAT 2K
- approx. 0.30 kg/m² (2 coats)
- Application conditions
- +10…+30 °C, max. 80% humidity
- Walkable (20 °C)
- after 24–48 hours
- Full cure (indoors)
- up to 4–5 days
Important
The substrate must be sound, clean and dry: moisture max. 9%, pH max. 10. VIRANIX 1K stone carpet must not be applied to substrates with rising ground moisture.
Products
System components
-
From 6.990 Ft6.990 Ft/kg View
-
From 19.490 Ft19.490 Ft/kg View
-
Vehicle traffic
VIRANIX PRIMECOAT 2K PRO – Heavy-duty topcoat (5:1)
Heavy-duty topcoat for garages, on medium-grain stone carpet.
From 22.990 Ft View -
Choosing a color
VIRANIX Stone Carpet Sample (10x10 cm)
Samples, so you can see the color in person before deciding.
1.990 Ft View -
12.990 Ft View
-
Edges
Edge Protection and Closing Profile
Aluminum edge protection and closing profile for stone carpet edges.
From 3.490 Ft View
Systems
1K or 2K PRO?
The two systems are independent of each other: they differ in material, primer and application, so their components must not be mixed.
Pre-mixed · water-based
VIRANIX 1K stone carpet
Factory pre-mixed marble pebbles with a water-based binder: simply stir thoroughly before application. Indoors and outdoors, on floors and walls.
Layer build-up
- 01TERRALOCK 1K primer
- 02VIRANIX stone carpet
- 03PRIMECOAT 2K topcoat
- On floors
- 4–6 mm
- On walls
- 2–4 mm
- Packaging
- 25 kg
Not suitable for substrates with rising ground moisture.
Mixed on site · aliphatic PUVIRANIX 2K PRO stone carpet
Marble aggregate and a two-component aliphatic polyurethane binder, mixed on site. An open-pored, water-permeable, UV-resistant covering for heavily used outdoor surfaces.
Layer build-up
- 012K PRO PU Primer
- 022K PRO Aggregate + PU Binder
- Layer
- min. 8 mm
- Pot life
- 45–50 min
- Surface
- open-pored
Water-permeable covering: it does not replace waterproofing.
FAQ
Frequently asked questions
Can't find the answer? Call us at +36 70 575 5500 or write to info@viranix.hu.
What is pre-mixed VIRANIX stone carpet?
A single-component, factory pre-mixed covering: natural marble pebbles with a water-based binder. No component dosing or mixing ratios; simply stir thoroughly before application.
Is a primer required?
Yes, it must not be applied without a primer. TERRALOCK 1K binds dust, evens out absorbency and forms a bonding bridge. Apply it with a roller in a thin, continuous layer, approx. 0.15 kg/m².
Is a topcoat required?
Yes, the 1K system always receives a 2K topcoat: PRIMECOAT 2K, or PRIMECOAT 2K PRO for vehicle traffic. Without a topcoat, the surface remains open-pored.
Can it be applied over old tiles?
Yes, if the tiling is stable: it does not sound hollow, does not move and is not damp. The clean, grease-free, matted tiles receive a quartz-sand BETOGRIP bonding bridge, followed by TERRALOCK 1K primer.
Can it be applied to walls?
Yes, it also holds on vertical surfaces. On walls, we work with fine-grain material in a 2–4 mm layer.
Can cars drive on it?
Yes, with the right layer build-up: medium grain, 6–8 mm layer thickness, TERRALOCK 1K primer and PRIMECOAT 2K PRO topcoat. Without these, it is not suitable for vehicle traffic.
Is it water-permeable or watertight?
Without a topcoat, the stone carpet is water-permeable. The PRIMECOAT 2K topcoat seals the pores, giving a closed, easy-to-clean surface. The covering does not replace waterproofing.
When can I walk on it?
At 20 °C it is typically walkable after 24–48 hours; full cure indoors can take up to 4–5 days. The topcoat may only be applied after full cure.
Which colors are available?
In 25 colors (KSZ01–KSZ25) and two grain sizes. We recommend requesting a color sample before deciding.
Where can I find the safety data sheet?
Contact
Calculate it yourself or request a quote
Our technical support helps contractors and private customers alike choose the right layer build-up.
Material calculatorEnter the size of the area and we will calculate how much material you need for the 1K system.Calculate
Color sampleRequest a sample and see the color in person, in your own lighting conditions.Request a sample
QuoteTell us the size of the area and the location, and we will put together a quote.Request a quote