VIRANIX AQUASHIELD ACRYL UV-1K (Acrylic-Based Waterproofing)
Water-based, one-component, acrylic-based flexible waterproofing coating in white and gray. Ready to use with no components to mix; applied by roller or brush.
A 1 mm layer needs approx. 1.5 kg/m². Calculate the exact quantity
Application guide and technical data further down the page
VIRANIX AQUASHIELD ACRYL UV-1K (Acrylic-Based Waterproofing)
Felhasználás
Where can you use it?
Once cured, it forms a seamless, flexible, UV-resistant, crack-bridging layer for waterproofing and renovating roofs, gutters and outdoor surfaces.
-
Sloped terrace roofs
Including renovation of old roofs.
-
Metal roofs, corrugated sheet roofs
Waterproofing of metal roof surfaces.
-
Gutters
Concrete, zinc and precast gutters.
-
Exterior walls, wet areas
Waterproofing of exterior walls.
Kivitelezés
Application step by step
Ready-to-use material: the primer is made from the same product, thinned with water. The second coat can be applied after 4–8 hours of drying.
-
Prepare the substrate
The surface must be clean, sound and free of laitance, loose parts, dust, grease and oil. If necessary, prepare it by water-jet or mechanical cleaning.
-
Prime with thinned material
Apply the product thinned with water at a ratio of 1 : 3 as a primer.
-
Apply the first coat
Stir the contents of the bucket and apply the first coat by roller or brush. Embed the ARMURNET reinforcement fabric into the still-wet coat.
Tipp Embed the fabric into the still-wet coat without creases.
-
Apply the final coat
After 4–8 hours of drying, apply the second coat, completely covering the fabric.
Tipp After application, tools can be cleaned with water before the material cures.
Calculator
How much waterproofing do you need?
Enter the area and the layer thickness. A 1 mm layer needs approx. 1.5 kg/m² of material; one bucket holds 5 kg.
Enter the surface area in square meters.
- Material required
- –
- Recommended quantity
- –
- Estimated price
- –
For reinforcement, the same area of ARMURNET reinforcement fabric is needed.
Adatlap
Technical data
- Chemical structure
- Elastomeric resin, water-based
- Color
- White (off-white), gray
- Density
- 1.37 g/cm³
- Solids content
- 70%
- Elongation
- 300%
- Waiting time between coats
- 4–8 hours
- Material consumption
- approx. 1.5 kg/m² per 1 mm layer thickness
- Application tool
- Roller, brush
- Tool cleaning
- With water, before curing
- Storage
- Protected from frost, in the closed original container
- Packaging
- 5 kg
Safe use
Signal word: Warning
- Irritant
- H315Causes skin irritation.
- H319Causes serious eye irritation.
- H335May cause respiratory irritation.
- P101If medical advice is needed, have product container or label at hand.
- P102Keep out of reach of children.
- P261Avoid breathing vapors/spray.
- P280Wear protective gloves and eye protection.
- P305+
P351+ IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P338 - P501Dispose of contents/container in accordance with local regulations.
Water-based, solvent-free, non-flammable. Hungarian Toxicological Information Service (ETTSZ, 0–24 h): +36 80 201 199 (toll-free), +36 1 476 6464.
GYIK
Frequently asked questions
Can't find the answer? Call us at +36 70 575 5500 or write to info@viranix.hu.
Does it need mixing?
No components need to be mixed: it is a ready-to-use one-component material. Simply stir the contents of the bucket thoroughly before application.
How much do I need?
Approx. 1.5 kg/m² for a 1 mm layer. For example, a 20 m² roof at 1 mm thickness needs approx. 30 kg, i.e. 6 buckets. You can calculate the exact quantity with the calculator.
Is a primer needed?
Yes. Apply the product thinned with water at a ratio of 1 : 3 as a primer.
How long do I need to wait between coats?
4–8 hours.
Is it suitable for surfaces exposed to sunlight?
Yes, it is UV-resistant and can also be used on surfaces exposed to direct sunlight.
Does it need reinforcing with fabric?
It can be reinforced with fabric: embed the ARMURNET reinforcement fabric into the first, still-wet coat and make sure the second coat covers it completely.
Which colors are available?
White (off-white) and gray.
What can tools be cleaned with?
With water, before the material cures.
How should I store it?
Protected from frost, in the closed original container.
What protective equipment is needed?
Protective gloves and eye protection are mandatory; do not breathe vapors or spray.
Rendszer
You may also need
-
For reinforcement
ARMURNET (Glass-Fiber Reinforcement Fabric)
Embedded in the first, still-wet coat, it reinforces the waterproofing.
2.490 Ft2.490 Ft/m2 View -
For cracks
CRACKBAND – Self-Adhesive Butyl Rubber Tape
For sealing static cracks and connections beneath the waterproofing.
2.490 Ft View -
For corners
SEALBAND FLEX - Flexible Waterproofing Tape
For reinforcing connections and corners, embedded in the waterproofing.
990 Ft View
Request a quote for roof renovation
Waterproofing a larger roof or terrace? Tell us the size of the area and we will help you calculate the material requirement.